Loading the KDP Cover Calculator...
- Spine width = page count x paper thickness per page.
- Full cover width = bleed + back cover + spine + front cover + bleed.
- White paper is 0.002252 in per page and cream paper is 0.0025 in per page.
- KDP only prints spine text on books with more than 79 pages.
How to use the KDP cover calculator
Enter the page count
Use the final page count of your interior file, including blank pages. KDP paperbacks run from 24 to 828 pages.
Choose the interior paper
Pick black ink on white, black ink on cream, standard color or premium color. Each has a different thickness.
Enter the trim size
Type the trim width and height in inches, such as 6 by 9 or 5.5 by 8.5.
Read the spine and cover size
The result shows the spine width, the full cover width and height with bleed, and the size in pixels at 300 DPI.
How the cover size is calculated
A paperback cover is one flat image that wraps around the book: back cover, spine and front cover, with a small bleed around the outside so the design runs to the edge after trimming. The spine depends on how thick the paper stack is, so more pages and thicker paper give a wider spine.
Spine width
Spine width = page count x paper thickness per page
White paper and standard color: 0.002252 in per page
Cream paper: 0.0025 in per page
Premium color: 0.002347 in per page
These are the per-page thicknesses KDP publishes for paperbacks.
Full cover size
Width = bleed + trim width + spine + trim width + bleed
Height = trim height + 2 x bleed
Pixels = inches x DPI
KDP uses a bleed of 0.125 in on each outside edge. Covers are normally built at 300 DPI.
KDP cover size examples
300 pages, white paper, 6 x 9 in
A black ink paperback with the most common trim size.
- Spine width 300 x 0.002252 = 0.676 in
- Full cover width 0.125 + 6 + 0.676 + 6 + 0.125 = 12.93 in
- Full cover height 9 + 0.25 = 9.25 in
- Pixels at 300 DPI 3878 x 2775
The spine is about 17.2 mm wide, so there is room for readable spine text.
200 pages, cream paper, 5.5 x 8.5 in
A fiction paperback on cream paper.
- Spine width 200 x 0.0025 = 0.500 in
- Full cover width 0.125 + 5.5 + 0.5 + 5.5 + 0.125 = 11.75 in
- Full cover height 8.5 + 0.25 = 8.75 in
- Pixels at 300 DPI 3525 x 2625
Cream paper is thicker, so the same page count gives a wider spine than white paper.
150 pages, standard color, 6 x 9 in
A color workbook.
- Spine width 150 x 0.002252 = 0.338 in
- Full cover width 12.59 in
- Pixels at 300 DPI 3776 x 2775
Always confirm against the template KDP generates for your exact book.
Spine width by page count (white paper)
Spine width table
White paper at 0.002252 in per page.
- 100 pages 0.225 in
- 150 pages 0.338 in
- 200 pages 0.450 in
- 300 pages 0.676 in
- 400 pages 0.901 in
- 500 pages 1.126 in
Add 0.25 in to the width of the two covers plus spine for the bleed.
Common KDP cover mistakes
- Forgetting the bleed: the full cover must extend 0.125 inches past the trim on each outer edge.
- Using a page count or paper type different from the final interior, which changes the spine width.
- Placing text or faces too close to the trim or spine, where they may be cut or folded.
- Low-resolution images that look blurry in print.
- Not leaving room on the back for the barcode.
KDP also offers its own cover calculator and templates, linked in the sources below.
Where a KDP cover calculator helps
Briefing a cover designer
Give your designer the exact spine width and full cover size so the file is right the first time.
Avoiding upload errors
A cover with the wrong size is rejected or trimmed badly. Check the numbers before you upload.
Changing page count
See how adding or cutting pages changes the spine before you finalize the cover.
Comparing paper types
See how white, cream and color paper change the spine width of the same book.
This calculator follows the paper thicknesses KDP publishes. KDP builds its final cover template from your exact settings, so compare your numbers with it before you upload. To price the book, use the KDP royalty calculator.
KDP cover calculator FAQ
How do I calculate spine width for KDP?
Multiply the page count by the paper thickness per page. For white paper that is 0.002252 inches per page, so 300 pages gives 0.676 inches.
How big should a KDP paperback cover be?
The full cover width is the back cover, spine and front cover plus 0.125 in of bleed on each outside edge. The height is the trim height plus 0.25 in of bleed.
What is the KDP spine width for white and cream paper?
White paper is 0.002252 inches per page and cream paper is 0.0025 inches per page. Standard color is 0.002252 and premium color is 0.002347.
Can I put text on the spine?
KDP only prints spine text on books with more than 79 pages. Thin books have a spine that is too narrow for text.
What resolution should a KDP cover be?
Build the cover at 300 DPI. The calculator converts the full cover size into pixels so you can set up the file in your design tool.
Does this work for hardcovers?
No. The paper thickness values are for paperbacks. Hardcover covers include a case wrap and use different dimensions, so use the KDP template for those.
Why was my KDP cover rejected?
Common reasons are a wrong spine width, missing bleed, text too close to the edges or low-resolution images.