Engine Displacement Calculator

Calculate engine displacement in cubic inches, cc and liters from bore, stroke and the number of cylinders.

Loading the Engine Displacement Calculator...

Engine displacement in short
On this page

How to use the engine displacement calculator

1

Pick the units

Choose inches or millimeters for the bore and stroke.

2

Enter bore and stroke

Type the cylinder bore and the stroke length.

3

Enter the cylinders

Type the number of cylinders, from 1 to 24.

4

Read the result

See displacement in liters, cubic inches and cc, plus the volume of each cylinder and the bore to stroke ratio.

How engine displacement is calculated

Displacement formula

Cylinder volume = π ÷ 4 × bore² × stroke

Displacement = cylinder volume × number of cylinders

Conversions: 1 cubic inch = 16.387 cc, and 1 liter = 1,000 cc

Use the same unit for bore and stroke, and measure the stroke as the distance the piston travels.

Example 1: a V8

A V8 has a 4.000 inch bore and a 3.480 inch stroke.

  • Volume per cylinder Ï€ ÷ 4 × 4.000² × 3.480 = 43.73 cubic inches
  • Displacement 43.73 × 8 = 349.8 cubic inches
  • In cc and liters 5,733 cc, or 5.73 liters

The result is sold as a 350 cubic inch or 5.7 liter engine, because makers round the figure.

Example 2: four-cylinder engines

One four-cylinder has an 86 mm bore and 86 mm stroke. Another has a 3.74 inch bore and 3.31 inch stroke.

  • 86 mm square engine 1,998 cc, or 2.0 liters
  • Bore to stroke ratio 1.000 (square)
  • 3.74 × 3.31 inch engine 145.5 cubic inches, or 2.38 liters
  • Volume per cylinder About 595.9 cc

A bore to stroke ratio above 1 is oversquare, and below 1 is undersquare.

Bore, stroke and engine character

Displacement alone does not decide how an engine feels. A larger bore with a shorter stroke, called oversquare, allows bigger valves and higher RPM, while a longer stroke tends to favor low-speed torque. After you know the displacement, use the compression ratio calculator to plan the build, the carburetor CFM calculator to size the airflow and the horsepower calculator to compare torque and power.

Liters to cubic inches

LitersCubic inches
1.5 LAbout 92 ci
2.0 LAbout 122 ci
4.95 L (sold as 5.0)302 ci
5.73 L (sold as 5.7)350 ci
6.2 LAbout 378 ci

1 liter = 61.02 cubic inches. Engine names are usually rounded, which is why badges and exact figures differ.

Where an engine displacement calculator helps

Engine builds

Check what a new bore or stroke does to displacement.

Overbore planning

Estimate the gain from boring a block over standard.

Comparing engines

Convert between cubic inches, cc and liters.

Motorcycles and small engines

Work out cc from bore and stroke.

Cubic inches, cc and liters

The calculator converts for you, but a quick check helps: multiply cubic inches by 16.387 for cc, then divide by 1,000 for liters.

Engine displacement calculator FAQ

Multiply π ÷ 4 by the bore squared and the stroke to get one cylinder, then multiply by the number of cylinders.

Multiply cubic inches by 16.387 to get cc, then divide by 1,000. A 349.8 cubic inch engine is about 5.73 liters.

The bore is larger than the stroke. These engines often rev freely and allow larger valves.

Yes, engine size usually means displacement, shown in liters, cc or cubic inches.

The exact calculation gives a figure just under 350, and manufacturers round it for the model name.

Not always. Power also depends on RPM, airflow, compression, tuning and whether the engine is boosted.

About 378 cubic inches.

Sources and further reading

Embed this calculator on your website

Free to use on any site. Copy the code below and paste it into an HTML block on your page. Please keep the credit link under the calculator.

Show the embed code

Works with WordPress, Wix, Squarespace, Webflow and most site builders that allow HTML. How embedding works.

Estimates, not advice

PureCalculate’s calculators give estimates for planning and education. They aren’t financial, tax or legal advice. Fees and tax rules change, so check the official source before making a decision. Spotted a mistake? Please tell us through the contact page.

Scroll to Top