Feeds and Speeds Calculator

Calculate spindle RPM, feed rate and material removal rate for milling from cutting speed, tool diameter, flutes and chip load.

Loading the Feeds and Speeds Calculator...

Feeds and speeds in short
On this page

How to use the feeds and speeds calculator

1

Pick the units

Choose inches and SFM, or millimeters and meters per minute.

2

Enter the tool data

Type the cutting speed, tool diameter, number of flutes and chip load per tooth.

3

Add cut details (optional)

Open the advanced fields to add depth and width of cut, and the maximum spindle RPM of your machine.

4

Read the result

See spindle RPM, feed rate and material removal rate, and the actual cutting speed if the RPM was capped.

How feeds and speeds are calculated

Feeds and speeds formulas

RPM = SFM × 12 ÷ (π × diameter in inches)

Feed rate = RPM × flutes × chip load per tooth

Material removal rate = feed rate × depth of cut × width of cut

Metric RPM = cutting speed (m/min) × 1000 ÷ (π × diameter in mm)

The surface speed in SFM is how fast the cutting edge moves past the material, in feet per minute.

Example 1: aluminum with a 3-flute end mill

A 0.5 inch, 3-flute end mill runs at 600 SFM with a 0.003 inch chip load, cutting 0.25 inch deep and 0.1 inch wide.

  • RPM 600 × 12 ÷ (Ï€ × 0.5) = 4,584
  • Feed rate 4,584 × 3 × 0.003 = 41.25 inches per minute
  • Material removal rate 41.25 × 0.25 × 0.1 = 1.03 cubic inches per minute

These are starting values from tool data. Adjust them for your machine and setup.

Example 2: a machine with a speed limit

A 0.25 inch, 2-flute tool is run at 600 SFM with a 0.001 inch chip load, but the spindle tops out at 5,000 RPM.

  • Ideal RPM 600 × 12 ÷ (Ï€ × 0.25) = 9,167
  • Capped RPM 5,000
  • Feed rate 5,000 × 2 × 0.001 = 10.0 inches per minute
  • Actual cutting speed Ï€ × 0.25 × 5,000 ÷ 12 = about 327 SFM

When the spindle is the limit, the cutting speed falls below the target and the feed rate follows the lower RPM.

Using the numbers safely

Treat the results as a starting point. Tool makers publish cutting speed and chip load for each material and tool, and the right values also depend on machine rigidity, tool stick-out, depth and width of cut, coolant and workholding. Start conservatively, listen to the cut and raise the feed if the tool is rubbing instead of cutting. A chip load that is too small can wear the tool, and one that is too large can break it. For other shop and engine work, see the gear ratio calculator and the horsepower calculator.

Worked example: a 1/2-inch end mill

3-flute carbide end mill, 400 SFM, 0.002 in chip load

Example values only; use your tool maker’s data for your material.

  • Spindle RPM 3.82 × 400 ÷ 0.5 = 3,056 RPM
  • Feed rate 3,056 × 3 × 0.002 = 18.3 in/min

Start a little lower on a new setup, listen to the cut and check the chips before increasing.

Where a feeds and speeds calculator helps

CNC milling

Set a starting RPM and feed for a new tool.

Hobby routers

Work out a sensible feed for wood or plastic bits.

Job quoting

Estimate cutting time from the feed rate.

Tool wear

Check chip load when a tool wears or breaks early.

Chip load matters most

A correct RPM with the wrong chip load still cuts badly. Keep the chip load in the range your tool maker recommends, and adjust the feed rate, not only the RPM.

Feeds and speeds calculator FAQ

Multiply the cutting speed in SFM by 12, then divide by pi times the tool diameter in inches. For 600 SFM and a 0.5 inch tool the RPM is about 4,584.

Multiply RPM by the number of flutes and by the chip load per tooth. At 4,584 RPM, 3 flutes and 0.003 inch the feed is about 41.25 inches per minute.

Chip load is the thickness of material each tooth removes per revolution. It sets how the tool cuts and how long it lasts.

The tool maker publishes recommended values for each material. Use them as the starting point.

Enter the maximum spindle RPM in the advanced field. The calculator caps the RPM and shows the actual cutting speed.

Yes. Pick millimeters and enter the cutting speed in meters per minute, the diameter in mm and the chip load in mm.

Sources and further reading

Embed this calculator on your website

Free to use on any site. Copy the code below and paste it into an HTML block on your page. Please keep the credit link under the calculator.

Show the embed code

Works with WordPress, Wix, Squarespace, Webflow and most site builders that allow HTML. How embedding works.

Estimates, not advice

PureCalculate’s calculators give estimates for planning and education. They aren’t financial, tax or legal advice. Fees and tax rules change, so check the official source before making a decision. Spotted a mistake? Please tell us through the contact page.

Scroll to Top