Carburetor CFM Calculator

Find the airflow your engine needs in CFM from displacement, maximum RPM and volumetric efficiency, with nearby common carburetor sizes.

Loading the Carburetor CFM Calculator...

Carburetor CFM in short
On this page

How to use the carburetor CFM calculator

1

Enter displacement

Type the engine size and pick cubic inches, cc or liters.

2

Enter maximum RPM

Use the highest RPM the engine will run, not the idle or cruising speed.

3

Set volumetric efficiency

Enter a percentage. A mild street engine is often around 75 to 85%, and a built engine 90 to 100%.

4

Read the result

See the CFM needed and the next common carburetor sizes up and down.

How carburetor CFM is calculated

CFM formula

CFM = displacement (cubic inches) × maximum RPM × volumetric efficiency ÷ 3456

Conversions: 1 liter = 61.02 cubic inches, and 1 cubic inch = 16.387 cc

The 3456 comes from a four-stroke engine drawing in half its displacement per revolution, with cubic inches converted to cubic feet.

Example 1: a small-block V8

A 350 cubic inch engine runs to 6,000 RPM with 85% volumetric efficiency.

  • CFM 350 × 6,000 × 0.85 ÷ 3456 = 516.5
  • Nearby sizes 500 CFM below and 525 CFM above

The result falls between two common sizes, so the choice depends on how you use the engine.

Example 2: a tuned engine and a big block

A 302 cubic inch engine runs to 6,500 RPM at 95%. A 454 cubic inch engine runs to 5,500 RPM at 80%.

  • 302 cubic inch engine 302 × 6,500 × 0.95 ÷ 3456 = 539.6 CFM
  • 454 cubic inch engine 454 × 5,500 × 0.80 ÷ 3456 = 578.0 CFM

Higher RPM and efficiency raise the airflow need, even in a smaller engine.

Using the result to choose a size

The figure is the theoretical airflow at maximum RPM. A carburetor slightly smaller than the result often gives better throttle response and fuel mixing on the street, while a larger one suits an engine that spends its time at high RPM. Ratings are measured at a set test pressure, with most four-barrels rated at 1.5 inches of mercury and many two-barrels at 3.0, so do not compare ratings from different test levels. Get the engine size from the engine displacement calculator and check power with the horsepower calculator.

Worked example: 350 ci street engine

350 ci, 6,000 RPM maximum, 85% volumetric efficiency

CFM = cubic inches × RPM ÷ 3,456 × VE.

  • Airflow at 100% VE 350 × 6,000 ÷ 3,456 = 607.6 CFM
  • At 85% VE About 516 CFM

A carburetor around 600 CFM is a common choice for this kind of engine. Going much bigger often hurts low-speed throttle response.

Where a carburetor CFM calculator helps

Carburetor swaps

Pick a size before buying a new carburetor.

Engine builds

Match airflow to the cam, heads and intake.

Street or strip

Compare the need at different maximum RPM.

Comparing engines

See how displacement and RPM change airflow.

Volumetric efficiency is an estimate

Real volumetric efficiency changes with RPM and with the cam, heads and intake. Treat the result as a starting point and follow the advice of your engine or carburetor builder.

Carburetor CFM calculator FAQ

Multiply displacement in cubic inches by maximum RPM and volumetric efficiency, then divide by 3456. A 350 at 6,000 RPM and 85% needs about 516 CFM.

About 75 to 85% is a common estimate for a mild street engine and 90 to 100% for a built one. Use your engine builder number if you have it.

Not necessarily. An oversized carburetor can hurt throttle response and mixture quality at low airflow.

A four-stroke engine takes in half its displacement per revolution, and the figure converts cubic inches to cubic feet.

Yes. Pick the unit and the calculator converts to cubic inches.

The airflow need is the same, but fuel injection is sized by injector flow and throttle body, not by a carburetor CFM rating.

About 500 to 600 CFM for a typical street engine revving to 6,000 RPM.

Sources and further reading

Embed this calculator on your website

Free to use on any site. Copy the code below and paste it into an HTML block on your page. Please keep the credit link under the calculator.

Show the embed code

Works with WordPress, Wix, Squarespace, Webflow and most site builders that allow HTML. How embedding works.

Estimates, not advice

PureCalculate’s calculators give estimates for planning and education. They aren’t financial, tax or legal advice. Fees and tax rules change, so check the official source before making a decision. Spotted a mistake? Please tell us through the contact page.

Scroll to Top